收藏本站
8 Mbit Firmware Hub
A Microchip Technology Company
SST49LF008A
Data Sheet
Reset
A V IL on INIT# or RST# pin initiates a device reset. INIT# and RST# pins have the same function inter-
nally. It is required to drive INIT# or RST# pins low during a system reset to ensure proper CPU initial-
ization.
During a Read operation, driving INIT# or RST# pins low deselects the device and places the output
drivers, FWH[3:0], in a high-impedance state. The reset signal must be held low for a minimal duration
of time T RSTP. A reset latency will occur if a reset procedure is performed during a Program or Erase
operation. See Table 19, Reset Timing Parameters for more information. A device reset during an
active Program or Erase will abort the operation and memory contents may become invalid due to data
being altered or corrupted from an incomplete Erase or Program operation.
Write Operation Status Detection
The SST49LF008A device provides two software means to detect the completion of a Write (Program
or Erase) cycle, in order to optimize the system Write cycle time. The software detection includes two
status bits: Data# Polling (DQ 7 ) and Toggle Bit (DQ 6 ). The End-of-Write detection mode is incorpo-
rated into the FWH Read cycle. The actual completion of the nonvolatile write is asynchronous with the
system; therefore, either a Data# Polling or Toggle Bit read may be simultaneous with the completion
of the Write cycle. If this occurs, the system may possibly get an erroneous result, i.e., valid data may
appear to conflict with either DQ 7 or DQ 6 . In order to prevent spurious rejection, if an erroneous result
occurs, the software routine should include a loop to read the accessed location an additional two (2)
times. If both reads are valid, then the device has completed the Write cycle, otherwise the rejection is
valid.
Data# Polling (DQ 7 )
When the SST49LF008A device is in the internal Program operation, any attempt to read DQ 7 will pro-
duce the complement of the true data. Once the Program operation is completed, DQ 7 will produce
true data. Note that even though DQ 7 may have valid data immediately following the completion of an
internal Write operation, the remaining data outputs may still be invalid: valid data on the entire data
bus will appear in subsequent successive Read cycles after an interval of 1 μs. During internal Erase
operation, any attempt to read DQ 7 will produce a ‘0’. Once the internal Erase operation is completed,
DQ 7 will produce a ‘1’. Proper status will not be given using Data# Polling if the address is in the invalid
range.
Toggle Bit (DQ 6 )
During the internal Program or Erase operation, any consecutive attempts to read DQ 6 will produce
alternating ‘0’s and ‘1’s, i.e., toggling between 0 and 1. When the internal Program or Erase operation
is completed, the toggling will stop.
Multiple Device Selection
The four ID pins, ID[3:0], allow multiple devices to be attached to the same bus by using different ID
strapping in a system. When the SST49LF008A is used as a boot device, ID[3:0] must be strapped as
0000, all subsequent devices should use a sequential up-count strapping (i.e. 0001, 0010, 0011, etc.).
The SST49LF008A will compare the strapping values, if there is a mismatch, the device will ignore the
remainder of the cycle and go into standby mode. For further information regarding FWH device map-
?2011 Silicon Storage Technology, Inc.
13
DS25085A
10/11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SST49LF016C-33-4C-EIE-T IC FLASH SER LPC 16MBIT 40TSOP
SST49LF080A-33-4C-WHE-T IC FLASH SER LPC 8MBIT 32TSOP
SST49LF160C-33-4C-NHE IC FLASH SER LPC 16MBIT 32PLCC
ST40 DIAC 35-45V BILATERAL TRIG DO214
STRIKER SURGE SUPPRESSR 120V 7OUT 6'CORD
SUPER-7 SURGE SUPPRESSOR 7 OUT 7' CORD
SUPER6TEL12 SURGE SUPPR 7OUT 12'CORD W/RJ11
SUPER6TEL SURGE SUPPRESSOR 7OUT W/TEL
相关代理商/技术参数
SST49LF008A-33-4C-NH 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:2 Mbit / 3 Mbit / 4 Mbit / 8 Mbit Firmware Hub
SST49LF008A-33-4C-NHE 功能描述:闪存 8M (1Mx8) 33MHz Commercial Temp RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF008A-33-4C-NHE_ 制造商:Microchip Technology Inc 功能描述:
SST49LF008A-33-4C-NHE-T 功能描述:闪存 8M (1Mx8) 33MHz 3.0-3.6V Commercial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF008A-33-4C-NHE-T-CUT TAPE 制造商:Microchip 功能描述:SST49LF Series 8 Mbit 1024 K x 8 3.3 V Firmware Hub - PLCC-32
SST49LF008A-33-4C-WH 制造商:SST 制造商全称:Silicon Storage Technology, Inc 功能描述:2 Mbit / 3 Mbit / 4 Mbit / 8 Mbit Firmware Hub
SST49LF008A-33-4C-WHE 功能描述:闪存 8 MBIT FIRMWARE HUB RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
SST49LF008A-33-4C-WHE_ 制造商:Microchip Technology Inc 功能描述: